NUCLEAR SAFETY AND CONTROL ACTNuclear Non-proliferation Import and Export Control RegulationsP.C.2000-790 20005
31
Her Excellency the Governor General in Council, on the recommendation of the Minister of Natural Resources, pursuant to section 44 of the Nuclear Safety and Control Acta, hereby approves the annexed Nuclear Non-proliferation Import and Export Control Regulations made by the Canadian Nuclear Safety Commission on May 31, 2000.S.C. 1997, c. 9InterpretationThe definitions in this subsection apply in these Regulations.Act means the Nuclear Safety and Control Act. (Loi)controlled nuclear equipment means the controlled nuclear equipment and the parts and components for controlled nuclear equipment referred to in the schedule. (équipement nucléaire contrôlé)controlled nuclear information means the controlled nuclear information referred to in the schedule. (renseignement nucléaire contrôlé)controlled nuclear substance means a controlled nuclear substance referred to in the schedule. (substance nucléaire contrôlée)transit means the process of being transported through Canada after being imported into and before being exported from Canada, in a situation where the place of initial loading and the final destination are outside Canada. (transit)All controlled nuclear substances are prescribed as nuclear substances for the purpose of paragraph (d) of the definition nuclear substance in section 2 of the Act, with respect to the import and export of those substances.All controlled nuclear equipment is prescribed equipment for the purposes of the Act, with respect to the import and export of that equipment.All controlled nuclear information is prescribed information for the purposes of the Act, with respect to the import and export of that information, unless it is made public in accordance with the Act, the regulations made under the Act or a licence.ApplicationThese Regulations apply in respect of the import and export of controlled nuclear substances, controlled nuclear equipment and controlled nuclear information.Application for Licence to Import or ExportAn application for a licence to import or export a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information shall contain the following information:the applicant’s name, address and telephone number;a description of the substance, equipment or information, including its quantity and the number of the paragraph of the schedule in which it is referred to;the name and address of the supplier;the country of origin of the substance, equipment or information;the name, address and, where the application is for a licence to import, telephone number of each consignee;the intended end-use of the substance, equipment or information by the final consignee and the intended end-use location;the number of any licence to possess the substance, equipment or information; andwhere the application is in respect of a controlled substance that is Category I, II or III nuclear material, as defined in section 1 of the Nuclear Security Regulations, the measures that will be taken to facilitate Canada’s compliance with the Convention on the Physical Protection of Nuclear Material, INFCIRC/274/Rev.1.The Commission or any designated officer who is authorized to carry out the duties set out in paragraphs 37(2)(c) and (d) of the Act may request any other information that is necessary to enable the Commission or that officer to form the opinion referred to in subsection 24(4) of the Act.SOR/2010-106, s. 1Exemptions from Licence RequirementA person may carry on any of the following activities without a licence to carry on that activity:import a controlled nuclear substance referred to in Part B of the schedule;import controlled nuclear equipment referred to in paragraph A.3 or Part B of the schedule;import controlled nuclear information that relates to a controlled nuclear substance or controlled nuclear equipment referred to in paragraph A.3 or Part B of the schedule;import a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information for the purpose of placing it in transit;export a controlled nuclear substance, controlled nuclear equipment or controlled nuclear information after it has been in transit;import, in a quantity of 200 kg or less per shipment, a controlled nuclear substance referred to in paragraph A.1.3 of the schedule that is not for use in a nuclear reactor;export a controlled nuclear substance referred to in paragraph A.1.4 of the schedule that is not for use in a nuclear reactor to any Participating Government of the Nuclear Suppliers Group;import a controlled nuclear substance referred to in paragraph A.1.4 of the schedule that is not for use in a nuclear reactor;import a controlled nuclear substance referred to in paragraph A.1.5 of the schedule that is contained in a self-luminous source or self-luminous device; orexport, to any Participating Government of the Nuclear Suppliers Group a controlled nuclear substance referred to in paragraph A.1.5 of the schedule that is contained in a self-luminous source or self-luminous device, if that source or device contains less than 1 480 GBq of tritium.For greater certainty, the exemptions established in subsection (1) relate only to the activities specified in that subsection and do not derogate from the licence requirement imposed by section 26 of the Act in relation to other activities.Every person who exports a controlled nuclear substance under paragraph (1)(f) or (i) must, by January 31, submit to the Commission a written report that includes the following information regarding every export of the controlled nuclear substance in the previous calendar year:the exporter’s name, address and telephone number;a description of the controlled nuclear substance, including the quantity exported and country of origin;the date of export;the name and address of each consignee; andthe intended end-use and end-use location of the controlled nuclear substance as stated by the final consignee.Paragraph (1)(i) applies only to exports that are intended for end-use in States that are signatories to the Treaty on the Non-Proliferation of Nuclear Weapons that was signed by Canada at London and Washington on July 23, 1968 and at Moscow on July 29, 1968 and that came into force for Canada on March 5, 1970.SOR/2010-106, s. 2SOR/2025-196, s. 5Coming into ForceThese Regulations come into force on the day on which they are approved by the Governor in Council.(Sections 1 and 4)Controlled Nuclear Substances, Equipment and InformationThe following lists are reproduced, in rearranged form and with some modifications, from International Atomic Energy Agency Information Circulars INFCIRC/254/Rev.14/Part 1, INFCIRC/254/Rev.12/Part 2 and INFCIRC/209/Rev.5.List of Nuclear ItemsA.1. Controlled Nuclear SubstancesSpecial fissionable material, as follows:plutonium and all isotopes, alloys and compounds and any material that contains any of these substances; anduranium 233, uranium enriched in the isotopes 235 or 233 and all alloys and compounds and any material that contains any of these substances.NOTEParagraph A.1.1. does not includespecial fissionable material occurring as contaminants in laundry, packaging, shielding, equipment or biological samples;special fissionable material used as a sensing component in instruments in quantities of four effective grams or less; orplutonium 238 that is contained in heart pacemakers.Source materialThe following source materials in any form, including ore, concentrate, compound, metal or alloy, or incorporated in any substance, other than medicinals, and in which the concentration of source material is greater than 0.05 weight %:uranium that contains the mixture of isotopes that occurs in nature;uranium that is depleted in the isotope 235; andthorium.NOTEParagraph A.1.2. does not includesource material occurring as contaminants in laundry, packaging, shielding, equipment or biological samples; ordepleted uranium used as ballasts, counterweights or shielding for Class II prescribed equipment, as defined in section 1 of the Class II Nuclear Facilities and Prescribed Equipment Regulations, for radiation devices or for transport packaging; orthorium used in civil non-nuclear applications, including thorium contained in lamps, lights, welding rods and engine coatings. This exemption does not apply to bulk imports or exports of thorium for the manufacture of these items.Deuterium and heavy waterDeuterium, heavy water (deuterium oxide) and any other deuterium compound in which the ratio of deuterium to hydrogen atoms exceeds 1:5,000.NOTEParagraph A.1.3. does not includedeuterium contained in deuterium lamps;deuterium occurring as a contaminant in laundry, packaging, shielding, equipment or biological samples;any deuterium compound that is used for labelling purposes; ordeuterium contained in pharmaceutical products.Nuclear grade graphiteGraphite having a purity level better than 5 ppm boron equivalent and with a density greater than 1.50 g/cm3.NOTEParagraph A.1.4 does not include exports, in quantities of 1 kg or less per shipment, of nuclear grade graphite that is not for use in a nuclear reactor.TritiumTritium, tritium compounds or mixtures containing tritium in which the ratio of tritium to hydrogen by atoms exceeds 1 part in 1000 and products that contain any of these substances.NOTEParagraph A.1.5 does not includetritium contained in self-luminous devices, for illumination, that have been installed in conveyances, including aircrafts, ships or vehicles;tritium contained in watches, compasses, jewellery or gunsights;tritium occurring as a contaminant in laundry, packaging, shielding, equipment or biological samples; ortritium contained in pharmaceutical products.A.2. Controlled Nuclear EquipmentNuclear reactors and especially designed or prepared equipment and components therefor, including:Complete nuclear reactorsNuclear reactors capable of operation so as to maintain a controlled self-sustaining fission chain reaction.Nuclear reactor vesselsMetal vessels, or major shop-fabricated parts for these vessels, especially designed or prepared to contain the core of a nuclear reactor within the meaning of paragraph A.2.1.1, as well as relevant nuclear reactor internals within the meaning of paragraph A.2.1.8.NOTEParagraph A.2.1.2 includes nuclear reactor vessels regardless of pressure rating, as well as reactor pressure vessels and calandrias. It includes the reactor vessel head as a major shop-fabricated part of a reactor vessel.Nuclear reactor fuel charging and discharging machinesManipulative equipment especially designed or prepared for inserting or removing fuel in a nuclear reactor within the meaning of paragraph A.2.1.1.Nuclear reactor control rods and equipmentEspecially designed or prepared rods, support or suspension structures for those rods, rod drive mechanisms or rod guide tubes to control the fission process in a nuclear reactor within the meaning of paragraph A.2.1.1.Nuclear reactor pressure tubesTubes especially designed or prepared to contain both fuel elements and the primary coolant in a nuclear reactor within the meaning of paragraph A.2.1.1.Nuclear fuel claddingZirconium metal tubes or zirconium alloy tubes, or assemblies of tubes, especially designed or prepared for use as fuel cladding in a nuclear reactor within the meaning of paragraph A.2.1.1.Primary coolant pumps or circulatorsPumps or circulators especially designed or prepared for circulating the primary coolant for a nuclear reactor within the meaning of paragraph A.2.1.1.Nuclear reactor internalsNuclear reactor internals especially designed or prepared for use in a nuclear reactor within the meaning of paragraph A.2.1.1. This includes, for example, support columns for the core, fuel channels, calandria tubes, thermal shields, baffles, core grid plates and diffuser plates.Heat exchangers, as follows:steam generators especially designed or prepared for the primary, or intermediate, coolant circuit of a nuclear reactor within the meaning of paragraph A.2.1.1; orother heat exchangers especially designed or prepared for use in the primary coolant circuit of a nuclear reactor within the meaning of paragraph A.2.1.1.NOTEParagraph A.2.1.9 does not include the emergency cooling system or the decay heat cooling system.Neutron detectorsEspecially designed or prepared neutron detectors for determining neutron flux levels within the core of a nuclear reactor within the meaning of paragraph A.2.1.1.External thermal shieldsExternal thermal shields especially designed or prepared for use in a nuclear reactor within the meaning of paragraph A.2.1.1 for reduction of heat loss and for containment vessel protection.Plants for the reprocessing of irradiated fuel elements, and equipment especially designed or prepared for that purpose, including:Irradiated fuel element decladding equipment and chopping machinesRemotely operated equipment especially designed or prepared for use in reprocessing plants referred to in paragraph A.2.2 and intended to expose or prepare the irradiated nuclear material in fuel assemblies, bundles or rods for processing.DissolverDissolver vessels or dissolvers employing mechanical devices especially designed or prepared for use in reprocessing plants referred to in paragraph A.2.2, intended for the dissolution of irradiated nuclear fuel and that are capable of withstanding hot, highly corrosive liquid, and that can be remotely loaded, operated and maintained.Solvent extractors and solvent extraction equipmentEspecially designed or prepared solvent extractors such as packed or pulse columns, mixer settlers or centrifugal contactors for use in reprocessing plants referred to in paragraph A.2.2. Solvent extractors must be resistant to the corrosive effect of nitric acid. Solvent extractors are normally fabricated to extremely high standards (including special welding and inspection and quality assurance and quality control techniques) out of low carbon stainless steels, titanium, zirconium or other high-quality materials.Chemical holding or storage vesselEspecially designed or prepared holding or storage vessels for use in reprocessing plants referred to in paragraph A.2.2. The holding or storage vessels must be resistant to the corrosive effect of nitric acid. The holding or storage vessels are normally fabricated of materials such as low carbon stainless steels, titanium or zirconium, or other high-quality materials. Holding or storage vessels may be designed for remote operation and maintenance and may have the following features for control of nuclear criticality:walls or internal structures with a boron equivalent of at least 2%;a maximum diameter of 175 mm (7 in.) for cylindrical vessels; ora maximum width of 75 mm (3 in.) for either a slab or annular vessel.Neutron measurement systems for process controlNeutron measurement systems especially designed or prepared for integration and use with automated process control systems in reprocessing plants referred to in paragraph A.2.2.[Repealed, SOR/2010-106, s. 10]Plants for the fabrication of nuclear reactor fuel elements, and equipment especially designed or prepared for that purpose, including equipment that:normally comes in direct contact with, or directly processes, or controls, the production flow of nuclear material;seals the nuclear material within the cladding;checks the integrity of the cladding or the seal;checks the finish treatment of the sealed fuel; oris used for assembling reactor fuel elements.NOTESuch equipment or systems of equipment may include any of the following:fully automatic pellet inspection stations especially designed or prepared for checking final dimensions and surface defects of the fuel pellets;automatic welding machines especially designed or prepared for welding end caps onto the fuel pins (or rods);automatic test and inspection stations especially designed or prepared for checking the integrity of completed fuel pins (or rods);systems especially designed or prepared to manufacture nuclear fuel cladding.Plants for the separation of isotopes of natural uranium, depleted uranium or special fissionable material and equipment, other than analytical instruments, especially designed or prepared for that purpose, includingGas centrifuges and assemblies and components especially designed or prepared for use in gas centrifuges, including:Rotating componentscomplete rotor assemblies:thin-walled cylinders, or a number of interconnected thin-walled cylinders, manufactured from one or more of the high strength to density ratio materials. If interconnected, the cylinders are joined together by flexible bellows or rings as described in paragraph (c). The rotor is fitted with an internal baffle(s) and end caps, as described in paragraphs (d) and (e), if in final form. However the complete assembly may be delivered only partly assembled;rotor tubes:especially designed or prepared thin-walled cylinders with a thickness of 12 mm or less, a diameter of between 75 mm and 650 mm, and manufactured from high strength to density ratio materials;rings or bellows:components especially designed or prepared to give localized support to the rotor tube or to join together a number of rotor tubes. The bellows is a short cylinder with a wall thickness of 3 mm or less, a diameter of between 75 mm and 650 mm, having a convolute, and manufactured from high strength to density ratio materials;baffles:disc-shaped components of between 75 mm and 650 mm in diameter especially designed or prepared to be mounted inside the centrifuge rotor tube, in order to isolate the take-off chamber from the main separation chamber and, in some cases, to assist the UF6 gas circulation within the main separation chamber of the rotor tube, and manufactured from high strength to density ratio materials; andtop caps or bottom caps:disc-shaped components of between 75 mm and 650 mm in diameter especially designed or prepared to fit to the ends of the rotor tube, and so contain the UF6 within the rotor tube, and in some cases to support, retain or contain as an integrated part an element of the upper bearing (top cap) or to carry the rotating elements of the motor and lower bearing (bottom cap), and manufactured from high strength to density ratio materials.NOTEThe materials used for centrifuge rotating components include the following:maraging steel capable of an ultimate tensile strength of 1.95 GPa or more;aluminium alloys capable of an ultimate tensile strength of 0.46 GPa or more; andfilamentary materials suitable for use in composite structures and having a specific modulus of 3.18 × 106 m or greater and a specific ultimate tensile strength of 7.62 × 104 m or greater (specific modulus is the Young’s Modulus in N/m2 divided by the specific weight in N/m3 and specific ultimate tensile strength is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3).Static componentsmagnetic suspension bearings:especially designed or prepared bearing assemblies consisting of an annular magnet suspended within a housing containing a damping medium. The housing will be manufactured from a UF6-resistant material. The magnet couples with a pole piece or a second magnet fitted to the top cap described in paragraph A.2.4.1.1(e). The annular magnet may have a relationship between an outer and inner diameter smaller or equal to 1.6:1. It may also be in a form having an initial permeability of 0.15 H/m or more, or a remanence of 98.5% or more, or an energy product of greater than 80 kJ/m3. In addition to the usual material properties, it is a prerequisite that the deviation of the magnetic axes from the geometrical axes is limited to very small tolerances (lower than 0.1 mm) or that homogeneity of the material of the magnet is specially called for; oractive magnetic bearings especially designed or prepared for use in gas centrifuges;bearings/dampers:especially designed or prepared bearings comprising a pivot/cup assembly mounted on a damper. The pivot is normally a hardened steel shaft with a hemisphere at one end with a means of attachment to the bottom cap described in paragraph A.2.4.1.1.(e) at the other. The shaft may however have a hydrodynamic bearing attached. The cup is pellet-shaped with a hemispherical indentation in one surface. These components are often supplied separately to the damper;molecular pumps:especially designed or prepared cylinders having internally machined or extruded helical grooves and internally machined bores. Typical dimensions are as follows: 75 mm to 650 mm internal diameter, 10 mm or more wall thickness, with the length equal to or greater than the diameter. The grooves are typically rectangular in cross-section and 2 mm or more in depth;motor stators:especially designed or prepared annular stators for high speed multiphase AC hysteresis (or reluctance) motors for synchronous operation within a vacuum at a frequency of 600 Hz or greater and a power of 40 VA or greater. The stators may consist of multiphase windings on a laminated low-loss iron core comprised of thin layers typically 2 mm thick or less;centrifuge housing or recipients:components especially designed or prepared to contain the rotor tube assembly of a gas centrifuge. The housing consists of a rigid cylinder of wall thickness up to 30 mm with precision-machined ends to locate the bearings and with one or more flanges for mounting. The machined ends are parallel to each other and perpendicular to the cylinder’s longitudinal axis to within 0.05° or less. The housing may also be a honeycomb-type structure to accommodate several rotor assemblies; andscoops:especially designed or prepared tubes for the extraction of UF6 gas from within the rotor tube by a Pitot tube action (that is, with an aperture facing into the circumferential gas flow within the rotor tube, for example by bending the end of a radially disposed tube) and capable of being fixed to the central gas extraction system.Especially designed or prepared auxiliary systems, equipment and components for gas centrifuge enrichment plants, including the following:Feed systems or product and tails withdrawal systemsEspecially designed or prepared process systems or equipment for enrichment plants, made of or protected by materials resistant to corrosion by UF6 includingfeed autoclaves, ovens or systems used for passing UF6 to the enrichment process;desublimers, cold traps or pumps used to remove UF6 from the enrichment process for subsequent transfer upon heating;solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; andproduct and tails stations used for transferring UF6 into containers.Machine header piping systemsEspecially designed or prepared piping systems and header systems for handling UF6 within the centrifuge cascades. The piping system is normally of the triple header type with each centrifuge connected to each of the headers. There is thus a substantial amount of repetition in its form. It is wholly made of or protected by UF6-resistant materials and is fabricated to very high vacuum and cleanliness standards.Special shut-off and control valvesshut-off valves especially designed or prepared to act on the feed, product or tails UF6 gas streams of a gas centrifuge; orbellows-sealed valves, manual or automated shut-off or control, made of or protected by materials resistant to corrosion by UF6, with an inside diameter of 10 mm to 160 mm, especially designed or prepared for use in main or auxiliary systems of gas centrifuge enrichment plants.UF6 mass spectrometers with ion sourcesEspecially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;ion sources made of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;electron bombardment ionization sources; anda collector system suitable for isotopic analysis.Frequency changersFrequency changers (also known as converters or inverters) especially designed or prepared to supply motor stators within the meaning of paragraph A.2.4.1.2(d), or parts, components and sub-assemblies of such frequency changers, having both of the following characteristics:a multiphase frequency output of 600 Hz or greater; andhigh stability (with frequency control better than 0.2%).Especially designed or prepared assemblies and components for use in gaseous diffusion enrichment, including:Gaseous diffusion barriers and barrier materialsespecially designed or prepared thin, porous filters, with a pore size of 10 nm to 100 nm, a thickness of 5 mm or less, and for tubular forms, a diameter of 25 mm or less, made of metallic, polymer or ceramic materials resistant to corrosion by UF6; andespecially prepared compounds or powders for the manufacture of such filters. Such compounds and powders include nickel or alloys containing 60% by weight or greater nickel, aluminium oxide, or UF6-resistant fully fluorinated hydrocarbon polymers having a purity of 99.9% by weight or greater, a particle size less than 10 µm, and a high degree of particle size uniformity, which are especially prepared for the manufacture of gaseous diffusion barriers.Diffuser housingsEspecially designed or prepared hermetically sealed cylindrical vessels for containing the gaseous diffusion barrier, made of or protected by UF6-resistant materials.Compressors and gas blowersEspecially designed or prepared compressors and gas blowers with a suction volume capacity of 1 m3/min or more of UF6 and a discharge pressure of up to 500 kPa, designed for long-term operation in the UF6 environment, as well as separate assemblies of such compressors and gas blowers. These compressors and gas blowers have a pressure ratio of 10:1 or less and are made of or protected by materials resistant to UF6.Rotary shaft sealsEspecially designed or prepared vacuum seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor or the gas blower rotor with the driver motor so as to ensure a reliable seal against in-leaking of air into the inner chamber of the compressor or gas blower, which is filled with UF6. Such seals are normally designed for a buffer gas in-leakage rate of less than 1 000 cm3/min.Heat exchangers for cooling UF6Especially designed or prepared heat exchangers made of or protected by UF6-resistant materials and intended for a leakage pressure change rate of less than 10 Pa/hour under a pressure difference of 100 kPa.Especially designed or prepared auxiliary systems, equipment and components for use in gaseous diffusion enrichment, including:Feed systems or product and tails withdrawal systemsEspecially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, includingfeed autoclaves, ovens or systems used for passing UF6 to the enrichment process;desublimers (or cold traps) or pumps used to remove UF6 from the enrichment process for subsequent transfer upon heating;solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; andproduct or tails stations used for transferring UF6 into containers.Header piping systemsEspecially designed or prepared piping systems and header systems for handling UF6 within the gaseous diffusion cascades. This piping network is normally of the double header system with each cell connected to each of the headers.Vacuum systemsespecially designed or prepared vacuum manifolds, vacuum headers and vacuum pumps having a suction capacity of 5 m3/min or more; andvacuum pumps especially designed for service in UF6-bearing atmospheres, made of or protected by materials resistant to corrosion by UF6. These pumps may be either rotary or positive, may have displacement and fluorocarbon seals and may have special working fluids present.Special shut-off and control valvesEspecially designed or prepared bellows-sealed valves, manual or automated, shut-off or control, made of or protected by materials resistant to corrosion by UF6, for installation in main and auxiliary systems of gaseous diffusion enrichment plants.UF6 mass spectrometers with ion sourcesEspecially designed or prepared mass spectrometers capable of taking on-line samples, from UF6 gas streams and having all of the following characteristics:the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;electron bombardment ionization sources; anda collector system suitable for isotopic analysis.Especially designed or prepared systems, equipment and components for use in aerodynamic enrichment plants, including:Separation nozzlesEspecially designed or prepared separation nozzles and separation nozzle assemblies. The separation nozzles consist of slit-shaped, curved channels having a radius of curvature of less than 1 mm, resistant to corrosion by UF6 and having a knife-edge within the nozzle that separates the gas flowing through the nozzle into two fractions.Vortex tubesEspecially designed or prepared vortex tubes and vortex tube assemblies. The vortex tubes are cylindrical or tapered, made of or protected by materials resistant to corrosion by UF6, and with one or more tangential inlets. The tubes may be equipped with nozzle-type appendages at either or both ends.Compressors and gas blowersEspecially designed or prepared compressors or gas blowers made of or protected by materials resistant to corrosion by the UF6 carrier gas (hydrogen or helium) mixture.Rotary shaft sealsEspecially designed or prepared rotary shaft seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor rotor or the gas blower rotor with the driver motor so as to ensure a reliable seal against out-leakage of process gas or in-leakage of air or seal gas into the inner chamber of the compressor or gas blower which is filled with a UF6/carrier gas mixture.Heat exchangers for gas coolingEspecially designed or prepared heat exchangers made of or protected by materials resistant to corrosion by UF6.Separation element housingsEspecially designed or prepared separation element housings, made of or protected by materials resistant to corrosion by UF6, for containing vortex tubes or separation nozzles.Feed systems/product and tails withdrawal systemsEspecially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, including:feed autoclaves, ovens, or systems used for passing UF6 to the enrichment process;desublimers (or cold traps) used to remove UF6 from the enrichment process for subsequent transfer upon heating;solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; andproduct or tails stations used for transferring UF6 into containers.Header piping systemsEspecially designed or prepared header piping systems, made of or protected by materials resistant to corrosion by UF6, for handling UF6 within the aerodynamic cascades. This piping network is normally of the double header design with each stage or group of stages connected to each of the headers.Vacuum systems and pumpsespecially designed or prepared vacuum systems, including vacuum manifolds, vacuum headers and vacuum pumps, designed for service in UF6-bearing atmospheres; andvacuum pumps especially designed or prepared for service in UF6-bearing atmospheres and made of or protected by materials resistant to corrosion by UF6. These pumps may use fluorocarbon seals and special working fluids.Special shut-off and control valvesEspecially designed or prepared bellows-sealed valves, manual or automated, shut-off or control, made of or protected by materials resistant to corrosion by UF6 and with a diameter of 40 mm or greater, for installation in main and auxiliary systems of aerodynamic enrichment plants.UF6 mass spectrometers with ion sourcesEspecially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;electron bombardment ionization sources; andcollector system suitable for isotopic analysis.UF6/carrier gas separation systemsEspecially designed or prepared process systems for separating UF6 from carrier gas (hydrogen or helium).Especially designed or prepared systems, equipment and components for use in chemical exchange or ion exchange enrichment plants, including:Liquid-liquid exchange columns (chemical exchange)Countercurrent liquid-liquid exchange columns with mechanical power input, especially designed or prepared for uranium enrichment using the chemical exchange process. For corrosion resistance to concentrated hydrochloric acid solutions, these columns and their internals are generally made of or protected by suitable plastic materials (such as fluorinated hydrocarbon polymers) or glass. The stage residence time of the columns is normally designed to be 30 s or less.Liquid-liquid centrifugal contactors (chemical exchange)Liquid-liquid centrifugal contactors especially designed or prepared for uranium enrichment using the chemical exchange process. Such contactors use rotation to achieve dispersion of the organic and aqueous streams and then centrifugal force to separate the phases. For corrosion resistance to concentrated hydrochloric acid solutions, the contactors are generally made of or protected by suitable plastic materials (such as fluorinated hydrocarbon polymers) or glass. The stage residence time of the centrifugal contactors is normally designed to be 30 s or less.Uranium reduction systems and equipment (chemical exchange)especially designed or prepared electrochemical reduction cells to reduce uranium from one valence state to another for uranium enrichment using the chemical exchange process. The cell materials in contact with process solutions must be corrosion resistant to concentrated hydrochloric acid solutions; andespecially designed or prepared systems at the product end of the cascade for taking the U+4 out of the organic stream, adjusting the acid concentration and feeding to the electrochemical reduction cells.Feed preparation systems (chemical exchange)Especially designed or prepared systems for producing high-purity uranium chloride feed solutions for chemical exchange uranium isotope separation plants.Uranium oxidation systems (chemical exchange)Especially designed or prepared systems for oxidation of U+3 to U+4 for return to the uranium isotope separation cascade in the chemical exchange enrichment process.Fast-reacting ion exchange resins/adsorbents (ion exchange)Fast-reacting ion-exchange resins or adsorbents especially designed or prepared for uranium enrichment using the ion exchange process, including porous macroreticular resins, and pellicular structures in which the active chemical exchange groups are limited to a coating on the surface of an inactive porous support structure, and other composite structures in any suitable form including particles or fibres. These ion exchange resins/adsorbents have diameters of 0.2 mm or less and must be chemically resistant to concentrated hydrochloric acid solutions as well as physically strong enough so as not to degrade in the exchange columns. The resins/adsorbents are especially designed to achieve very fast uranium isotope exchange kinetics (exchange rate half-time of less than 10 s) and are capable of operating at a temperature in the range of 100°C to 200°C.Ion exchange columns (ion exchange)Cylindrical columns greater than 1 000 mm in diameter for containing and supporting packed beds of ion exchange resin/adsorbent, especially designed or prepared for uranium enrichment using the ion exchange process. These columns are made of or protected by materials (such as titanium or fluorocarbon plastics) resistant to corrosion by concentrated hydrochloric acid solutions and are capable of operating at a temperature in the range of 100°C to 200°C and pressures above 0.7 MPa (102 psi).Ion exchange reflux systems (ion exchange)especially designed or prepared chemical or electrochemical reduction systems for regeneration of the chemical reducing agent(s) used in ion exchange uranium enrichment cascades; andespecially designed or prepared chemical or electrochemical oxidation systems for regeneration of the chemical oxidizing agent(s) used in ion exchange uranium enrichment cascades.Especially designed or prepared systems, equipment and components for use in laser-based enrichment plants, including:Uranium vaporization systems (Atomic Vapour Laser Isotope Separation)Especially designed or prepared uranium vaporization systems for use in laser enrichment.Liquid or vapour uranium metal handling systems and components (Atomic Vapour Laser Isotope Separation)Especially designed or prepared systems for handling molten uranium, molten uranium alloys or uranium metal vapour for use in laser enrichment, or especially designed or prepared components for that purpose.Uranium metal product and tails collector assemblies (Atomic Vapour Laser Isotope Separation)Especially designed or prepared product and tails collector assemblies for collecting uranium metal in liquid or solid form.Separator module housings (Atomic Vapour Laser Isotope Separation)Especially designed or prepared cylindrical or rectangular vessels for containing the uranium metal vapour source, the electron beam gun, and the product and tails collectors.Supersonic expansion nozzles (Molecular Laser Isotope Separation)Especially designed or prepared supersonic expansion nozzles for cooling mixtures of UF6 and carrier gas to 150 K (-123°C) or less and that are corrosion resistant to UF6.Product or tails collectors (Molecular Laser Isotope Separation)Especially designed or prepared components or devices for collecting uranium product material or uranium tails material following illumination with laser light.UF6/carrier gas compressors (molecular laser isotope separation)Especially designed or prepared compressors for UF6/carrier gas mixtures, designed for long-term operation in a UF6 environment. The components of these compressors that come into contact with process gas are made of or protected by materials resistant to corrosion by UF6.Rotary shaft seals (molecular laser isotope separation)Especially designed or prepared rotary shaft seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor rotor with the driver motor so as to ensure a reliable seal against out-leakage of process gas or in-leakage of air or seal gas into the inner chamber of the compressor which is filled with a UF6/carrier gas mixture.Fluorination systems (molecular laser isotope separation)Especially designed or prepared systems for fluorinating UF5 (solid) to UF6 (gas).UF6 mass spectrometers with ion sources (Molecular Laser Isotope Separation)Especially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following characteristics:the capability of measuring ions of 320 atomic mass units or greater with a resolution of better than 1 part in 320;ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60% by weight or more, or nickel-chrome alloys;electron bombardment ionization sources; andcollector system suitable for isotopic analysis.Feed systems/product and tails withdrawal systems (molecular laser isotope separation)Especially designed or prepared process systems or equipment for enrichment plants made of or protected by materials resistant to corrosion by UF6, including:feed autoclaves, ovens, or systems used for passing UF6 to the enrichment process;desublimers (or cold traps) used to remove UF6 from the enrichment process for subsequent transfer upon heating;solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form; andproduct or tails stations used for transferring UF6 into containers.UF6/carrier gas separation systems (molecular laser isotope separation)Especially designed or prepared process systems for separating UF6 from carrier gas. The carrier gas may be nitrogen, argon, or other gas.Laser systemsLasers or laser systems especially designed or prepared for the separation of uranium isotopes.Especially designed or prepared systems, equipment and components for use in plasma separation enrichment plants, including:Microwave power sources and antennaeEspecially designed or prepared microwave power sources and antennae for producing or accelerating ions and having the following characteristics: greater than 30 GHz frequency and greater than 50 kW mean power output for ion production.Ion excitation coilsEspecially designed or prepared radio frequency ion excitation coils for frequencies of more than 100 kHz and capable of handling more than 40 kW mean power.Uranium plasma generation systemsEspecially designed or prepared systems for the generation of uranium plasma for use in plasma separation plants.[Repealed, SOR/2025-196, s. 34]Uranium metal product and tails collector assembliesEspecially designed or prepared product and tails collector assemblies for uranium metal in solid form. These collector assemblies are made of or protected by materials resistant to the heat and corrosion of uranium metal vapour, such as yttria-coated graphite or tantalum.Separator module housingsCylindrical vessels especially designed or prepared for use in plasma separation enrichment plants for containing the uranium plasma source, radio-frequency drive coil and the product and tails collectors.Especially designed or prepared systems, equipment and components for use in electromagnetic enrichment plants, including:Electromagnetic isotope separatorsElectromagnetic isotope separators especially designed or prepared for the separation of uranium isotopes, and equipment and components therefor, including:ion sources:especially designed or prepared single or multiple uranium ion sources consisting of a vapour source, ionizer, and beam accelerator, constructed of suitable materials such as graphite, stainless steel, or copper, and capable of providing a total ion beam current of 50 mA or greater;ion collectors:collector plates consisting of two or more slits and pockets especially designed or prepared for collection of enriched and depleted uranium ion beams and constructed of suitable materials such as graphite or stainless steel;vacuum housings:especially designed or prepared vacuum housings for uranium electromagnetic separators, constructed of suitable non-magnetic materials such as stainless steel and designed for operation at pressures of 0.1 Pa or lower; andmagnet pole pieces:especially designed or prepared magnet pole pieces having a diameter greater than 2 m used to maintain a constant magnetic field within an electromagnetic isotope separator and to transfer the magnetic field between adjoining separators.High voltage power suppliesEspecially designed or prepared high-voltage power supplies for ion sources, having all of the following characteristics: capable of continuous operation, output voltage of 20 000 V or greater, output current of 1 A or greater, and voltage regulation of better than 0.01% over a time period of 8 hours.Magnet power suppliesEspecially designed or prepared high-power, direct current magnet power supplies having all of the following characteristics: capable of continuously producing a current output of 500 A or greater at a voltage of 100 V or greater and with a current or voltage regulation better than 0.01% over a period of 8 hours.Plants for the production or concentration of heavy water, deuterium and deuterium compounds and equipment especially designed or prepared therefor, including:Water-hydrogen sulphide exchange towersExchange towers with diameters of 1.5 m or greater and capable of operating at pressures greater than or equal to 2 MPa, especially designed or prepared for heavy water production utilizing the water-hydrogen sulphide exchange process.Blowers and compressorsSingle stage, low head (i.e., 0.2 MPa) centrifugal blowers or compressors for hydrogen sulphide gas circulation (i.e., gas containing more than 70% by weight of hydrogen sulphide), especially designed or prepared for heavy water production utilizing the water-hydrogen sulphide exchange process. These blowers or compressors have a throughput capacity greater than or equal to 56 m3/s while operating at pressures greater than or equal to 1.8 MPa suction and have seals designed for wet hydrogen sulphide service.Ammonia-hydrogen exchange towersAmmonia-hydrogen exchange towers greater than or equal to 35 m in height with diameters of 1.5 m to 2.5 m and capable of operating at pressures greater than 15 MPa, especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process. These towers also have at least one flanged, axial opening of the same diameter as the cylindrical part through which the internals can be inserted or withdrawn.Tower internals and stage pumpsTower internals and stage pumps especially designed or prepared for towers for heavy water production utilizing the ammonia-hydrogen exchange process. Tower internals include especially designed stage contactors which promote intimate gas/liquid contact. Stage pumps include especially designed submersible pumps for circulation of liquid ammonia within a contacting stage internal to the stage towers.Ammonia crackersAmmonia crackers with operating pressures greater than or equal to 3 MPa (450 psi) especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.Infrared absorption analyzersInfrared absorption analyzers capable of on-line hydrogen to deuterium ratio analysis if deuterium concentrations are equal to or greater than 90% by weight.Catalytic burnersCatalytic burners for the conversion of enriched deuterium gas into heavy water especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.Complete heavy water upgrade systems or columns for those systemsComplete heavy water upgrade systems, or columns for them, especially designed or prepared for the upgrade of heavy water to reactor-grade deuterium concentration.Ammonia synthesis converters or synthesis unitsAmmonia synthesis converters or synthesis units especially designed or prepared for heavy water production utilizing the ammonia-hydrogen exchange process.Plants for the conversion of uranium and plutonium for use in the fabrication of fuel elements and the separation of uranium isotopes, as set out in paragraphs A.2.3. and A.2.4., respectively, and equipment especially designed or prepared for such plants, includingPlants for the conversion of uranium and equipment especially designed or prepared for that purpose, includingEspecially designed or prepared systems for the conversion of uranium ore concentrates to UO3.Especially designed or prepared systems for the conversion of UO3 to UF6.Especially designed or prepared systems for the conversion of UO3 to UO2.Especially designed or prepared systems for the conversion of UO2 to UF4.Especially designed or prepared systems for the conversion of UF4 to UF6.Especially designed or prepared systems for the conversion of UF4 to U metal.Especially designed or prepared systems for the conversion of UF6 to UO2.Especially designed or prepared systems for the conversion of UF6 to UF4.Especially designed or prepared systems for the conversion of UO2 to UCl4.Plants for the conversion of plutonium and equipment especially designed or prepared for that purpose, includingEspecially designed or prepared systems for the conversion of plutonium nitrate to oxide.Especially designed or prepared systems for plutonium metal production.A.3. Parts for Controlled Nuclear Equipment Identified in Paragraphs Comprising A.2.NOTEParagraph A.3 includes parts designed or prepared for controlled nuclear equipment identified in paragraphs comprising A.2.A.4. Controlled Nuclear InformationTechnologyTechnical data for the design, production, construction, operation or maintenance of any item in this part, including, but not limited to, blueprints, plans, diagrams, models, formulae, engineering designs and specifications, software, manuals and instructions, except data available to the public (e.g., publications, publicly available websites, or that which has been made available without restrictions on its further dissemination).NOTETechnical data referred to in paragraph A.4.1 is subject to control under both tangible and intangible modes of transfer.List of Nuclear-related Dual-use ItemsB.1. Controlled Nuclear SubstancesNuclear-related dual-use substancesRadionuclides appropriate for making neutron sources based on alpha-n reaction as follows:actinium-225 (225Ac);actinium-227 (227Ac);californium-253 (253Cf);curium-240 (240Cm);curium-241 (241Cm);curium-242 (242Cm);curium-243 (243Cm);curium-244 (244Cm);einsteinium-253 (253Es);einsteinium-254 (254Es);gadolinium-148 (148Gd);plutonium-236 (236Pu);plutonium-238 (238Pu);polonium-208 (208Po);polonium-209 (209Po);polonium-210 (210Po);radium-223 (223Ra);thorium-227 (227Th);thorium-228 (228Th);uranium-230 (230U); anduranium-232 (232U).NOTEThese radionuclides may be in elemental form or may be contained in:compounds having a total radioactivity of 37 GBq/kg or greater;mixtures having a total radioactivity of 37 GBq/kg or greater;products or devices containing anything referred to in paragraphs (a) and (b), except a product or device containing a compound or mixture having a total radioactivity of less than 3.7 GBq; orproducts or devices containing radionuclides in elemental form, except a product or device having a total radioactivity of less than 3.7 GBq.Aluminium alloys capable of an ultimate tensile strength of 0.46 GPa or more at 293 K, in the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm.NOTEThe phrase “capable of” encompasses aluminium alloys before or after heat treatment.Beryllium metal, alloys containing more than 50% beryllium by weight, beryllium compounds, and manufactures thereof, except:metal windows for X-ray machines, or for bore-hole logging devices;oxide shapes in fabricated or semi-fabricated forms specially designed for electronic component parts or as substrates for electronic circuits; andberyl (silicate of beryllium and aluminium) in the form of emeralds or aquamarines.NOTEThis entry includes waste and scrap containing beryllium as defined above.Bismuth having both of the following characteristics:a purity of 99.99% or greater by weight;a silver content of less than 10 ppm by weight.Boron and boron compounds, mixtures, loaded materials, and waste or scrap of any of these substances, in which the boron-10 isotope is more than 20% by weight of the total boron content.Calcium (high purity) containing both less than 1 000 ppm by weight of metallic impurities other than magnesium and less than 10 ppm of boron.Chlorine trifluoride (ClF3).Crucibles made of materials resistant to liquid actinide metals, as follows:crucibles with a volume of between 150 ml and 8 L and made of or coated with any of the following materials having a purity of 98% or greater:calcium fluoride (CaF2)calcium zirconate (metazirconate) (Ca2ZrO3)cerium sulfide (Ce2S3)erbium oxide (erbia) (Er2O3)hafnium oxide (hafnia) (HfO2)magnesium oxide (MgO)nitrided niobium-titanium-tungsten alloy (approximately 50%Nb, 30%Ti, 20%W)yttrium oxide (yttria) (Y2O3)zirconium oxide (zirconia) (ZrO2);crucibles with a volume of between 50 ml and 2 L and made of or lined with tantalum, having a purity of 99.9% or greater; andcrucibles with a volume of between 50 ml and 2 L and made of or lined with tantalum (having a purity of 98% or greater) coated with tantalum carbide, nitride, or boride (or any combination of these).Fibrous or filamentary materials, prepregs and composite structures, as follows:carbon or aramid fibrous or filamentary materials having a specific modulus of 12.7 x 106 m or greater or a specific tensile strength of 23.5 x 104 m or greater, except aramid fibrous or filamentary materials having 0.25% or more by weight of an ester based fibre surface modifier;glass fibrous or filamentary materials having a specific modulus of 3.18 x 106 m or greater and a specific tensile strength of 7.62 x 104 m or greater; andthermoset resin impregnated continuous yarns, rovings, tows or tapes with a width no greater than 15 mm (prepregs), made from carbon or glass fibrous or filamentary materials specified in paragraph (a) or (b).NOTEThe resin forms the matrix of the composite.composite structures in the form of tubes with an inside diameter of between 75 mm (3 in.) and 400 mm (16 in.) made with any of the fibrous or filamentary materials specified in paragraph (a) or carbon prepreg materials specified in paragraph (c).NOTEfibrous or filamentary materials means continuous monofilaments, yarns, rovings, tows or tapes.specific modulus is the Young’s modulus in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 23 ± 2°C and a relative humidity of 50 ± 5%.specific tensile strength is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 23 ± 2°C and a relative humidity of 50 ± 5%.Hafnium metal, alloys, compounds of hafnium containing more than 60% hafnium by weight, and their manufactures, and waste or scrap of any of these substances.Helium-3 or mixtures, products or devices containing helium-3, except a product or device containing less than 1 g of helium-3.Lithium having any of the following characteristics:enriched in the lithium-6 isotope (6Li) to greater than 7.5 atom percent;enriched in the lithium-6 isotope contained in alloys, compounds, mixtures, waste or scrap;conforming to the description in paragraph (a) or (b) and contained in products or devices, except thermoluminescent dosimeters.NOTEThe natural occurrence of the 6 isotope in lithium is 7.5 atom per cent.Magnesium (high purity) containing both less than 200 ppm by weight of metallic impurities other than calcium and less than 10 ppm of boron.Maraging steel capable of an ultimate tensile strength of 1 950 MPa or more at 293 K, except forms in which no linear dimension exceeds 75 mm.NOTEThe phrase “capable of” encompasses maraging steel before or after heat treatment.Nickel powder and porous nickel metal, as follows:powder with a nickel purity content of 99% or greater and a mean particle size of less than 10 µm measured by the ASTM B 330 standard, except filamentary nickel powders; andNOTENickel powders which are specially prepared for the manufacture of gaseous diffusion barriers are controlled under paragraph A.2.4.3.1.(b).porous nickel metal produced from materials referred to in paragraph (a), except single porous nickel metal sheets not exceeding 1 000 cm2 per sheet.NOTEThis refers to porous metal formed by compacting and sintering the material referred to in paragraph (a) to form a metal material with fine pores interconnected throughout the structure.Radium-226, radium-226 alloys, radium-226 compounds, or mixtures containing radium-226, products manufactured from them and products or devices containing any of them, except medical applicators and a product or device containing not more than 0.37 GBq of radium-226 in any form.Titanium alloys capable of an ultimate tensile strength of 900 MPa or more at 293 K in the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm.NOTEThe phrase “capable of” encompasses titanium alloys before or after heat treatment.Tungsten, tungsten carbide, or tungsten alloys (greater than 90% tungsten by weight) having a mass greater than 20 kg and in forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 mm and 300 mm, except parts specifically designed for use as weights or gamma-ray collimators.Zirconium with a hafnium content of less than 1 part hafnium to 500 parts zirconium by weight, in the form of metal, alloys containing more than 50% zirconium by weight, and compounds and manufactures of these things; except zirconium in the form of foil having a thickness not exceeding 0.10 mm (0.004 in.).NOTEParagraph B.1.1.19. applies to waste and scrap containing zirconium as defined above.Rhenium, alloys containing 90% or more by weight of rhenium, and alloys of rhenium and tungsten containing 90% or more by weight of any combination of rhenium and tungsten, having both of the following characteristics:a form with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 mm and 300 mm; anda mass greater than 20 kg.Any substance not otherwise included in paragraph B.1 if the substance is intended, or there are reasonable grounds to suspect that it is intended, in whole or in part, for use in connection with the design, development, production, handling, operation, maintenance or storage of nuclear weapons or other nuclear explosive devices.B.2. Controlled Nuclear EquipmentIndustrial equipmentFlow-forming machines and spin-forming machines capable of flow-forming functions, and mandrels, as follows, and specially designed software for them:machines having three or more rollers (active or guiding) and that, according to the manufacturer’s technical specification, can be equipped with numerical control units or a computer control; androtor-forming mandrels designed to form cylindrical rotors of inside diameter between 75 mm and 650 mm.NOTEParagraph (a) includes machines that have only a single roller designed to deform metal and two auxiliary rollers that support the mandrel but do not participate directly in the deformation process.Machine tools and specially designed software as follows:machine tools, as set out below, and any combination of them, for removing or cutting metals, ceramics or composites, which, according to the manufacturer’s technical specifications, can be equipped with electronic devices for simultaneous contouring control in two or more axes:machine tools for turning, that have positioning accuracies with all compensations available better (less) than 0.006 mm according to ISO 230/2 (1988) along any linear axis (overall positioning) for machines capable of machining diameters greater than 35 mm;NOTEParagraph B.2.1.2.(a)(1) does not include bar machines (Swissturn) limited to machining only bar feed thru, if the maximum bar diameter is equal to or less than 42 mm and there is no capability of mounting chucks. Machines may have drilling and/or milling capabilities for machining parts with diameters less than 42 mm.machine tools for milling having any of the following characteristics:positioning accuracies with all compensations available are better (less) than 0.006 mm according to ISO 230/2 (1988) along any linear axis (overall positioning);two or more contouring rotary axes; orfive or more axes that can be coordinated simultaneously for contouring control;NOTEParagraph B.2.1.2.(a)(2) does not include milling machines having the following characteristics:x-axis travel greater than 2 m; andoverall positioning accuracy on the x-axis worse (more) than 0.030 mm according to ISO 230/2 (1988).machine tools for grinding having any of the following characteristics:positioning accuracies with all compensations available are better (less) than 0.004 mm according to ISO 230/2 (1988) along any linear axis (overall positioning);two or more contouring rotary axes; orfive or more axes that can be coordinated simultaneously for contouring control; andNOTEParagraph B.2.1.2.(a)(3) does not include the following grinding machines:cylindrical external, internal and external-internal grinding machines having all of the following characteristics:limited to a maximum workpiece capacity of 150 mm outside diameter or length; andaxes limited to x, z and c; andjig grinders that do not have a z-axis or a w-axis with an overall positioning accuracy less (better) than 0.004 mm (positioning accuracy is according to ISO 230/2 (1988)).non-wire type electrical discharge machines that have two or more contouring rotary axes and that can be coordinated simultaneously for contouring control; andNOTEParagraph B.2.1.2.(a) does not include special purpose machine tools limited to the manufacture of any of the following parts:gears;crankshafts or camshafts;tools or cutters; andextruder worms.software:software specially designed or modified for the development, production or use of equipment referred to in paragraph B.2.1.2.(a); andsoftware for any combination of electronic devices or systems enabling those devices to function as a numerical control unit capable of controlling five or more interpolating axes that can be coordinated simultaneously for contouring control.NOTESoftware is controlled whether exported separately or residing in a numerical control unit or any electronic device or system.Software specially designed or modified by the manufacturers of the control unit or machine tool to operate an uncontrolled machine tool is not controlled.Dimensional inspection machines, instruments or systems, as follows, and software specially designed for those machines, instruments or systems:computer controlled or numerically controlled coordinate measuring machines having either of the following characteristics:only two axes and a maximum permissible error (MPE) of length measurement along any axis (one-dimensional), identified as any combination of E0x MPE, E0y MPE or E0z MPE, equal to or less (better) than (1.25 + L/1 000) μm (where L is the measured length in mm) at any point within the operating range of the machine (i.e., within the length of the axis), according to ISO 10360-2:2009;three or more axes and a maximum permissible error (MPE) of three-dimensional (volumetric) length measurement (E0 MPE) equal to or less (better) than (1.7 + L/800) μm (where L is the measured length in mm) at any point within the operating range of the machine (i.e., within the length of the axis), according to ISO 10360-2:2009;linear displacement measuring instruments, as follows:non-contact type measuring systems with a resolution equal to or better (less) than 0.2 µm within a measuring range of up to 0.2 mm;linear variable differential transformer systems having both of the following characteristics:linearity equal to or better (less) than 0.1% within a measuring range of up to 5 mm; anddrift equal to or better (less) than 0.1% per day at a standard ambient test room temperature of ± 1 K; ormeasuring systems that have both of the following characteristics:contain a laser; andmaintain for at least 12 hours over a temperature range of ± 1 K around a standard temperature and a standard pressure:a resolution over their full scale of 0.1 µm or better; anda measurement uncertainty equal to or better (less) than (0.2 + L/2 000) µm (L is the measured length in millimeters);NOTEParagraph B.2.1.3(b)(3) does not include measuring interferometer systems, without closed or open loop feedback, containing a laser to measure slide movement errors of machine tools, dimensional inspection machines or similar equipment.angular measuring instruments having an angular position deviation equal to or better (less) than 0.00025°; andNOTEParagraph B.2.1.3.(c) does not include optical instruments, such as autocollimators, using collimated light (e.g. laser light) to detect angular displacement of a mirror.systems for simultaneous linear-angular inspection of hemishells, having both of the following characteristics:measurement uncertainty along any linear axis equal to or better (less) than 3.5 µm per 5 mm; andangular position deviation equal to or less than 0.02°.NOTESpecially designed software for these systems includes software for simultaneous measurements of wall thickness and contour.NOTEWith respect to paragraph B.2.1.3.:machine tools that can be used as measuring machines are included if they meet or exceed the criteria specified for the machine tool function or the measuring machine function;machines are included if they exceed the control threshold anywhere within their operating range; and[Repealed, SOR/2025-196, s. 52]all parameters of measurement values in paragraph B.2.1.3. represent plus/minus, i.e. not total band.Vacuum or controlled environment (inert gas) induction furnaces capable of operation above 850°C and having induction coils 600 mm (24 in.) or less in diameter, and designed for power inputs of 5 kW or more; and power supplies specially designed therefor with a specified power output of 5 kW or more.NOTEThis paragraph does not include furnaces designed for the processing of semiconductor wafers.Isostatic presses capable of achieving a maximum working pressure of 69 MPa or greater having a chamber cavity with an inside diameter in excess of 152 mm and specially designed dies, molds, controls or specially designed software therefor.NOTEThe inside chamber dimension is that of the chamber in which both the working temperature and the working pressure are achieved and does not include fixtures. That dimension will be the smaller of either the inside diameter of the pressure chamber or the inside diameter of the insulated furnace chamber, depending on which of the two chambers is located inside the other.The term isostatic presses means equipment capable of pressurizing a closed cavity through various media (gas, liquid, solid particles, etc.) to create equal pressure in all directions within the cavity upon a workpiece or material.Robots or end-effectors having characteristics set out in paragraphs (a) or (b) and specially designed software or specially designed control units for those devices:specially designed to comply with national safety standards applicable to handling high explosives (for example, meeting electrical code ratings for high explosives);specially designed or rated as radiation hardened to withstand greater than 5 x 104 Gy (Silicon) [5 x 106 rad (Silicon)] without operational degradation; andcontrol units specially designed for any of the robots or end-effectors specified in paragraph (a).NOTESRobot means a manipulation mechanism, which may be of the continuous path or of the point-to-point variety, may use sensors, and has all of the following characteristics:is multifunctional;is capable of positioning or orienting material, parts, tools, or special devices through variable movements in three-dimensional space;incorporates three or more closed or open loop servo-devices which may include stepping motors; andhas user-accessible programmability by means of teach/playback method or by means of an electronic computer which may be a programmable logic controlled, i.e., without mechanical intervention.The above definition does not include the following devices:manipulation mechanisms which are only manually/teleoperator controllable;fixed sequence manipulation mechanisms which are automated moving devices operating according to mechanically fixed programmed motions. The program is mechanically limited by fixed stops, such as pins or cams. The sequence of motions and the selection of paths or angles are not variable or changeable by mechanical, electronic, or electrical means;mechanically controlled variable sequence manipulation mechanisms which are automated moving devices operating according to mechanically fixed programmed motions. The program is mechanically limited by fixed, but adjustable, stops such as pins or cams. The sequence of motions and the selection of paths or angles are variable within the fixed program pattern. Variations or modifications of the program pattern (e.g., changes of pins or exchanges of cams) in one or more motion axes are accomplished only through mechanical operations;non-servo-controlled variable sequence manipulation mechanisms which are automated moving devices, operating according to mechanically fixed programmed motions. The program is variable but the sequence proceeds only by the binary signal from mechanically fixed electrical binary devices or adjustable stops; orstacker cranes defined as Cartesian coordinate manipulator systems manufactured as an integral part of a vertical array of storage bins and designed to access the contents of those bins for storage or retrieval.End-effectors include grippers, active tooling units, and any other tooling that is attached to the baseplate on the end of a robot manipulator arm.The definition in paragraph 1(a) does not include robots specially designed for non-nuclear industrial applications such as automobile paint-spraying booths.Vibration test systems, equipment, components and software therefor, as follows:electrodynamic vibration test systems, employing feedback or closed loop control techniques and incorporating a digital controller, capable of vibrating at 10 g RMS or more between 20 Hz and 2 000 Hz and capable of imparting forces of 50 kN measured bare table or greater;digital controllers, combined with specially designed software for vibration testing, with a real-time bandwidth greater than 5 kHz and being designed for use with the systems referred to in paragraph (a);vibration thrusters (shaker units), with or without associated amplifiers, capable of imparting a force of 50 kN (11,250 lbs.), measured bare table, or greater, which are usable for the systems referred to in paragraph (a);test piece support structures and electronic units designed to combine multiple shaker units into a complete shaker system capable of providing an effective combined force of 50 kN, measured bare table, or greater, which are usable for the systems referred to in paragraph (a); andspecially designed software for use with the systems referred to in paragraph (a) or for the electronic units referred to in paragraph (d).Vacuum or other controlled atmosphere metallurgical melting and casting furnaces and related equipment, as follows, as well as specially configured computer control and monitoring systems and specially designed software for that purpose:arc remelt furnaces, arc melt furnaces and arc melt and casting furnaces with consumable electrode capacities between 1 000 cm3 and 20 000 cm3 and capable of operating with melting temperatures above 1 700°C;electron beam melting furnaces, plasma atomization furnaces and plasma melting furnaces with a power of 50 kW or greater and capable of operating with melting temperatures above 1 200°C;plasma torches specially designed for the furnaces specified in paragraph (b) having both of the following characteristics:operating at a power greater than 50 kW; andcapable of operating above 1 200°C; andelectron beam guns specially designed for the furnaces specified in paragraph (b) operating at a power greater than 50 kW.Uranium isotope separation equipment and components (other than items listed in paragraph A.2.4.)Electrolytic cells for fluorine production with a production capacity greater than 250 g of fluorine per hour.Rotor fabrication and assembly equipment and bellows-forming mandrels and dies, as follows:rotor assembly equipment for assembly of gas centrifuge rotor tube sections, baffles, and end caps. Such equipment includes precision mandrels, clamps, and shrink fit machines;rotor straightening equipment for alignment of gas centrifuge rotor tube sections to a common axis; andbellows-forming mandrels and dies for producing single-convolution bellows (bellows made of high-strength aluminium alloys, maraging steel, or high-strength filamentary materials). The bellows have all of the following dimensions:75 mm to 650 mm inside diameter;12.7 mm or more in length;single convolution depth of more than 2 mm.Centrifugal multiplane balancing machines, fixed or portable, horizontal or vertical, as follows:centrifugal balancing machines designed for balancing flexible rotors having a length of 600 mm or more and having all of the following characteristics:a swing or journal diameter of 75 mm or more;mass capability of from 0.9 kg to 23 kg (2 lbs. to 50 lbs.); andcapable of balancing speed of revolution of more than 5 000 rpm; andcentrifugal balancing machines designed for balancing hollow cylindrical rotor components and having all of the following characteristics:a journal diameter of 75 mm or more;mass capability of from 0.9 kg to 23 kg (2 lbs. to 50 lbs.);capable of balancing to a residual imbalance of 0.010 kg mm/kg per plane or better; andbelt drive type;and specially designed software therefor.Filament winding machines and related equipment, as follows, and specially designed software for those machines and related equipment:filament-winding machines having all of the following characteristics:motions for positioning, wrapping and winding fibres coordinated and programmed in two or more axes;specially designed to fabricate composite structures or laminates from fibrous or filamentary materials; andcapable of winding cylindrical tubes with an internal diameter between 75 mm and 650 mm and lengths of 300 mm or greater;coordinating and programming controls for the filament-winding machines specified in paragraph (a);precision mandrels for the filament-winding machines specified in paragraph (a); andspecially designed software for the filament-winding machines specified in paragraph (a).Frequency changers (also known as converters or inverters) or generators usable as a variable frequency or fixed frequency motor drive, and related software:frequency changers or generators having all of the following characteristics;multiphase output capable of providing a power of 40 VA or greater;operating at a frequency of 600 Hz or greater;frequency control better (less) than 0.2%; andsoftware, as the case may bespecially designed for the use of equipment specified in paragraphs (a)(1) to (3);having encryption keys or codes specially designed to enhance or release the performance characteristics of equipment not included in paragraphs (a)(1) to (3) so that it meets or exceeds the characteristics specified in those paragraphs; orspecially designed to enhance or release the performance characteristics of the equipment.NOTEParagraph B.2.2.5 includes frequency changers intended for specific industrial machinery or consumer goods (machine tools, vehicles, etc.) if the frequency changers can meet the characteristics above when removed.Lasers, laser amplifiers, and oscillators as follows:copper vapour lasers with 30 W or greater average output power operating at wavelengths between 500 nm and 600 nm;argon ion lasers with greater than 40 W average output power operating at wavelengths between 400 nm and 515 nm;neodymium-doped (other than glass) lasers with an output wavelength of between 1 000 nm and 1 100 nm having either of the following characteristics:pulse-excited and Q-switched with a pulse duration equal to or greater than 1 ns, and having either of the following characteristics:single-transverse mode output having an average output power exceeding 40 W; ormultiple-transverse mode output having an average output power exceeding 50 W; orfrequency doubling incorporated to give an output wavelength between 500 nm and 550 nm with an average output power of greater than 40 W;tunable pulsed single-mode dye laser oscillators having all of the following characteristics:operation at wavelengths of between 300 nm and 800 nm;average output power greater than 1 W;repetition rate greater than 1 kHz; andpulse width less than 100 ns;tunable pulsed dye laser amplifiers and oscillators, except single mode oscillators, having all of the following characteristics:operation at wavelengths of between 300 nm and 800 nm;average output power greater than 30 W;repetition rate greater than 1 kHz; andpulse width less than 100 ns;alexandrite lasers having all of the following characteristics:operation at wavelengths of between 720 nm and 800 nm;average output power greater than 30 W;repetition rate greater than 125 Hz; andbandwidth of 0.005 nm or less;pulsed carbon dioxide lasers having all of the following characteristics:operation at wavelengths of between 9 000 nm and 11 000 nm;average output power greater than 500 W;repetition rate greater than 250 Hz; andpulse width less than 200 ns;NOTEParagraph B.2.2.6.(g) does not include the higher power (typically 1 kW to 5 kW) industrial CO2 lasers used in applications such as cutting and welding, as those lasers are either continuous wave or are pulsed with a pulse width of more than 200 ns.pulsed excimer lasers (XeF, XeCl, KrF) having all of the following characteristics:operation at wavelengths of between 240 nm and 360 nm;average output power greater than 500 W; andrepetition rate greater than 250 Hz;para-hydrogen Raman shifters designed to operate at 16 µm output wavelength and at a repetition rate greater than 250 Hz; andpulsed carbon monoxide lasers having all of the following characteristics:operating at wavelengths between 5 000 nm and 6 000 nm;an average output power greater than 200 W;a repetition rate greater than 250 Hz; andpulse width of less than 200 ns.Mass spectrometers capable of measuring ions of 230 atomic mass units or greater with a resolution of better than 2 parts in 230, and one of the following characteristics:inductively coupled plasma mass spectrometers (ICP/MS);glow discharge mass spectrometers (GDMS);thermal ionization mass spectrometers (TIMS);electron bombardment mass spectrometers having both of the following characteristics:a molecular beam inlet system that injects a collimated beam of analyte molecules into a region of the ion source where the molecules are ionized by an electron beam; andone or more cold traps that can be cooled to a temperature of 193 K (-80°C) or less in order to trap analyte molecules that are not ionized by the electron beam; andmass spectrometers equipped with a microfluorination ion source designed for actinides or actinide fluorides.[Repealed, SOR/2025-196, s. 59]All types of pressure transducers capable of measuring absolute pressure and having the following characteristics:pressure sensing elements made of or protected by aluminium, aluminium alloy, aluminium oxide (alumina or sapphire), nickel or nickel alloys containing more than 60% nickel by weight, or fully fluorinated hydrocarbon polymers;seals, if any, essential for sealing the pressure sensing element, and in direct contact with the process medium, made of or protected by aluminium, aluminium alloy, aluminium oxide (alumina or sapphire), nickel or nickel alloys containing more than 60% nickel by weight, or fully fluorinated hydrocarbon polymers;either of the following characteristics:a full scale of less than 13 kPa and an accuracy of better than ±1% of full scale; ora full scale of 13 kPa or greater and an accuracy of better than ±130 Pa when measuring at 13 kPa.NOTEPressure transducers are devices that convert pressure measurements into an electrical signal.For the purpose of this paragraph, accuracy includes non-linearity, hysteresis and repeatability at ambient temperature.Valves 5 mm (0.2 in.) or greater in nominal size, with a bellows seal, wholly made of or lined with aluminium, aluminium alloy, nickel, or alloy containing 60% or more nickel, either manually or automatically operated.NOTEFor valves with different inlet and outlet diameters, the nominal size parameter above refers to the smallest diameter.Superconducting solenoidal electromagnets with all of the following characteristics:capable of creating magnetic fields of more than 2 T (20 kilogauss);with an L/D (length divided by inner diameter) greater than 2;with an inner diameter of more than 300 mm; andwith a magnetic field uniform to better than 1% over the central 50% of the inner volume.NOTEThis paragraph does not cover magnets specially designed for and exported as parts of medical nuclear magnetic resonance (NMR) imaging systems. It is understood that the wording “as part of” does not necessarily mean physical part in the same shipment. Separate shipments from different sources are allowed, provided that the related export documents clearly specify the “part of” relationship.Vacuum pumps with an input throat size of 38 cm (15 in.) or greater with a pumping speed of 15,000 L/s or greater and capable of producing an ultimate vacuum better than 104 torrs (1.33 x 10-4 mbar).NOTEThe ultimate vacuum is determined at the input of the pump with the input of the pump blocked off.The pumping speed is determined at the measurement point with nitrogen gas or air.Direct current high-power supplies capable of continuously producing, over a time period of 8 hours, 100 V or greater with current output of 500 amps or greater and with current or voltage regulation better than 0.1%.High-voltage direct current power supplies capable of continuously producing, over a time period of 8 hours, 20 000 V or greater with current output of 1 amp or greater and with current or voltage regulation better than 0.1%.Electromagnetic isotope separators, designed for or equipped with, single or multiple ion sources capable of providing a total ion beam current of 50 mA or greater.NOTESThis paragraph includes separators capable of enriching stable isotopes as well as those for uranium. A separator capable of separating the isotopes of lead with a one-mass unit difference is inherently capable of enriching the isotope of uranium with three-unit mass difference.This paragraph includes separators with the ion sources and collectors both in the magnetic field and those configurations in which they are external to the field.A single 50 mA ion source will produce less than 3 g of separated HEU per year from natural abundance feed.Bellows-sealed scroll-type compressors and bellows-sealed scroll-type vacuum pumps having all of the following characteristics:capable of an inlet volume flow rate of 50 m3/h or greater;capable of a pressure ratio of 2:1 or greater; andhaving all surfaces that come in contact with the process gas made from any of the following materials:aluminium or aluminium alloy;aluminium oxide;stainless steel;nickel or nickel alloy;phosphor bronze; orfluoropolymers.NOTESIn a scroll-type compressor or vacuum pump, crescent-shaped pockets of gas are trapped between one or more pairs of intermeshed spiral vanes, or scrolls, one of which moves while the other remains stationary. The moving scroll orbits the stationary scroll and does not rotate. As the moving scroll orbits the stationary scroll, the gas pockets diminish in size (i.e., they are compressed) as they move toward the outlet port of the machine.In a bellows-sealed scroll-type compressor or vacuum pump, the process gas is totally isolated from the lubricated parts of the pump and from the external atmosphere by a metal bellows. One end of the bellows is attached to the moving scroll and the other end is attached to the stationary housing of the pump.Fluoropolymers include, but are not limited to, the following materials:polytetrafluoroethylene (PTFE);fluorinated ethylene propylene (FEP);perfluoroalkoxy (PFA);polychlorotrifluoroethylene (PCTFE); andvinylidene fluoride-hexafluoropropylene copolymer.Heavy water production plant-related equipment (other than items listed in paragraph A.2.5.).Specialized packings for use in separating heavy water from ordinary water and made of phosphor bronze mesh (chemically treated to improve wettability) and designed for use in vacuum distillation towers.Pumps circulating solutions of diluted or concentrated potassium amide catalyst in liquid ammonia (KNH2/NH3), with all of the following characteristics:airtight (i.e., hermetically sealed);for concentrated potassium amide solutions (1% or greater), operating pressure of 1.5 MPa to 60 MPa (15 to 600 atmospheres); for dilute potassium amide solutions (less than 1%), operating pressure of 20 MPa to 60 MPa (200 to 600 atmospheres); anda capacity greater than 8.5 m3/h (5 cu.ft./ min.).[Repealed, SOR/2025-196, s. 62]Hydrogen-cryogenic distillation columns having all of the following characteristics:designed for operation at internal temperatures of 35 K (-238ºC) or less;designed for operation at internal pressures of 0.5 MPa to 5 MPa;constructed of eitherstainless steels of SAE 300 series with low sulfur content and an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; orequivalent materials that are both cryogenic and H2-compatible; andhaving internal diameters of 30 cm or greater and effective lengths of 4 m or greater.[Repealed, SOR/2025-196, s. 62]Turboexpanders or turboexpander-compressor sets designed for operation below 35 K and a throughput of hydrogen gas of 1 000 kg/h or greater.Implosion systems development equipmentFlash x-ray generators or pulsed electron accelerators with peak energy of 500 keV or greater, as follows, except accelerators that are component parts of devices designed for purposes other than electron beam or x-ray radiation (electron microscopy, for example) and those designed for medical purposes:having an accelerator peak electron energy of 500 keV or greater but less than 25 MeV and with a figure of merit (K) of 0.25 or greater, where K is defined as:K=1.7 x 103V2.65Q;where V is the peak electron energy in million electron volts and Q is the total accelerated charge in coulombs if the accelerator beam pulse duration is less than or equal to 1 µs, if the acceleration beam pulse duration is greater than 1 µs, Q is the maximum accelerated charge in 1 µs [Q equals the integral of i with respect to t, over the lesser of 1 µs or the time duration of the beam pulse (Q =ƒidt), where i is beam current in amperes and t is the time in seconds]; orhaving an accelerator peak electron energy of 25 MeV or greater and a peak power greater than 50 MW. [Peak power = (peak potential in volts) x (peak beam current in amperes).]NOTESTime duration of the beam pulse means, in machines, based on microwave accelerating cavities, the time duration of the beam pulse is the lesser of 1 µs or the duration of the bunched beam packet resulting from one microwave modulator pulse.Peak beam current means, in machines, based on microwave accelerating cavities, the peak beam current is the average current in the time duration of a bunched beam packet.High-velocity gun systems (propellant, gas, coil, electromagnetic, and electrothermal types, and other advanced systems) capable of accelerating projectiles to 1.5 km/s or greater.NOTEParagraph B.2.4.2 does not control guns specially designed for high-velocity weapon systems.High-speed cameras and imaging devices, and components for those cameras or devices, as follows:streak cameras, and specially designed components for those cameras, as follows:streak cameras with writing speeds greater than 0.5 mm/µs;electronic streak cameras capable of 50 ns or less time resolution;streak tubes for cameras specified in paragraph (2);plug-ins specially designed for use with streak cameras having modular structures and that enable the performance specifications set out in paragraphs (1) and (2); andsynchronizing electronic units, and their rotor assemblies consisting of turbines, mirrors and bearings, specially designed for cameras specified in paragraph (1);framing cameras, and specially designed components for those cameras, as follows:framing cameras with recording rates greater than 225 000 frames per second;framing cameras capable of 50 ns or less frame exposure time;framing tubes and solid-state imaging devices having a fast image gating (shutter) time of 50 ns or less specifically designed for cameras specified in paragraphs (1) and (2);plug-ins specially designed for use with framing cameras having modular structures and that enable the performance specifications set out in paragraphs (1) and (2); andsynchronizing electronic units, and their rotor assemblies consisting of turbines, mirrors and bearings, specially designed for cameras specified in paragraphs (1) and (2); andsolid-state or electron tube cameras and specially designed components for those cameras, as follows:solid-state cameras or electron tube cameras, with a fast-image gating (shutter) time of 50 ns or less;solid-state imaging devices and image intensifier tubes having a fast-image gating (shutter) time of 50 ns or less specially designed for cameras specified in paragraph (1);electro-optical shutters (Kerr or Pockels cells) with a fast-image gating (shutter) time of 50 ns or less; andplug-ins specially designed for use with cameras having modular structures and that enable the performance specifications set out in paragraph (1).[Repealed, SOR/2025-196, s. 63]Specialized instrumentation for hydrodynamic experiments, as follows:velocity interferometers for measuring velocities exceeding 1 km/s during time intervals of less than 10 µs;shock pressure gauges capable of measuring pressures greater than 10 GPa, including gauges made with manganin, ytterbium and polyvinylidene fluoride (PVDF) or polyvinyl difluoride (PVF2); andquartz pressure transducers for pressures greater than 10 GPa.NOTEParagraph B.2.4.5(a) includes velocity interferometers such as velocity interferometer systems for any reflector (VISARs), Doppler laser interferometers (DLIs) and photonic Doppler velocimeters (PDVs), also known as heterodyne velocimeters (Het-V).High-explosive containment vessels, chambers, containers and other similar containment devices designed for the testing of high explosives or explosive devices and having both of the following characteristics:designed to fully contain an explosion equivalent to 2 kg of trinitrotoluene (TNT) or greater; andhaving design elements or features enabling real-time or delayed transfer of diagnostic or measurement information.Explosives and related equipmentDetonators and multipoint initiation systems (exploding bridge wire, slappers etc.):electrically driven explosive detonators, as follows:exploding bridge (EB);exploding bridge wire (EBW);slapper; andexploding foil initiators (EFI); andarrangements using single or multiple detonators designed to nearly simultaneously initiate an explosive surface (over greater than 5 000 mm2) from a single firing signal (with an initiation timing spread over the surface of less than 2.5 µs).NOTEThe detonators of concern all utilize a small electrical conductor (bridge, bridge wire or foil) that explosively vaporizes when a fast, high-current electrical pulse is passed through it. In nonslapper types, the exploding conductor starts a chemical detonation in a contacting high-explosive material such as PETN (pentaerythritoltetranitrate). In slapper detonators, the explosive vaporization of the electrical conductor drives a “flyer” or “slapper” across a chemical detonation. The slapper in some designs is driven by magnetic force. The term “exploding foil” detonator may refer to either an EB or a slapper-type detonator. Also, the word “initiator” is sometimes used in place of the word “detonator”.Detonators using only primary explosives, such as lead azide, are not subject to control.Electronic components for firing sets (switching devices and pulse discharge capacitors):switching devices:cold-cathode tubes (including gas krytron tubes and vacuum sprytron tubes), whether gas filled or not, operating similarly to a spark gap, containing three or more electrodes, and having all of the following characteristics:anode peak voltage rating of 2 500 V or more;anode peak current rating of 100 A or more; andanode delay time of 10 µs or less;triggered spark-gaps having an anode delay time of 15 µs or less and rated for a peak current of 500 A or more; andmodules or assemblies with a fast switching function having all of the following characteristics:anode peak voltage rating greater than 2 000 V;anode peak current rating of 500 A or more; andturn-on time of 1 µs or less; andcapacitors with the following characteristics:voltage rating greater than 1.4 kV, energy storage greater than 10 J, capacitance greater than 0.5 µF, and series inductance less than 50 nH; orvoltage rating greater than 750 V, capacitance greater than 0.25 µF, and series inductance less than 10 nH.Firing sets and equivalent high-current pulse generators, as follows:detonator firing sets (initiation systems, firesets), including electronically charged, explosively driven and optically driven firing sets designed to drive multiple controlled detonators specified in paragraph B.2.5.1;modular electrical pulse generators (pulsers) having all of the following characteristics:capable of delivering their energy in less than 15 µs into loads of less than 40 Ω;having an output greater than 100 A;designed for portable, mobile or ruggedized use;having no dimension greater than 30 cm;weighing less than 30 kg; andspecified to operate over an extended temperature range from 223 K to 373 K (-50°C to 100°C) or specified as suitable for aerospace applications; andmicro-firing units having all of the following characteristics:no dimension greater than 35 mm;voltage rating of equal to or greater than 1 kV;capacitance of equal to or greater than 100 nF.NOTEOptically driven firing sets include both those employing laser initiation and laser charging. Explosively driven firing sets include both explosive ferroelectric and explosive ferromagnetic firing set types. Paragraph B.2.5.3(b) includes xenon flashlamp drivers.High explosive substances or mixtures containing more than 2% by weight of any of the following:cyclotetramethylenetetranitramine (HMX) (CAS 2691-41-0);cyclotrimethylenetrinitramine (RDX) (CAS 121-82-4);triaminotrinitrobenzene (TATB) (CAS 3058-38-6);aminodinitrobenzo-furoxan or 7-amino-4,6 nitrobenzofurazane-1-oxide (ADNBF) (CAS 97096-78-1);1,1-diamino-2,2-dinitroethylene (DADE or FOX7) (CAS 145250-81-3);2,4-dinitroimidazole (DNI) (CAS 5213-49-0);diaminoazoxyfurazan (DAAOF or DAAF) (CAS 78644-89-0);diaminotrinitrobenzene (DATB) (CAS 1630-08-6);dinitroglycoluril (DNGU or DINGU) (CAS 55510-04-8);2,6-Bis(picrylamino)-3,5-dinitropyridine (PYX) (CAS 38082-89-2);3,3′-diamino-2,2′,4,4′,6,6′-hexanitrobiphenyl or dipicramide (DIPAM) (CAS 17215-44-0);diaminoazofurazan (DAAzF) (CAS 78644-90-3);1,4,5,8-tetranitro-pyridazino[4,5-d]pyridazine (TNP) (CAS 229176-04-9);hexanitrostilbene (HNS) (CAS 20062-22-0) or;any explosive with a crystal density greater than 1.8 g/cm3 and having a detonation velocity greater than 8 000 m/s.Striplines to provide a low inductance path to detonators and having both of the following characteristics:voltage rating greater than 2 kV; andinductance of less than 20 nH.Nuclear testing equipment and componentsPhotomultiplier tubes with a photocathode area greater than 20 cm2 having an anode pulse rise time of less than 1 ns.High-speed pulse generators and pulse heads with output voltages greater than 6 V into a resistive load of less than 55 Ω and with pulse transition times of less than 500 ps (defined as the time interval between 10% and 90% voltage amplitude).Other equipmentNeutron generator systems, including tubes, having all of the following characteristics:designed for operation without an external vacuum system; andutilizing electrostatic acceleration to inducea tritium-deuterium nuclear reaction; ora deuterium-deuterium nuclear reaction capable of an output of 3 × 109 neutrons/s or greater.Equipment related to nuclear material handling and processing and to nuclear reactors, as follows:remote manipulators that can be used to provide remote actions in radiochemical separation operations or hot cells, as follows:having a capability of penetrating 0.6 m or more of hot cell wall (through-the-wall operation); orhaving a capability of bridging over the top of a hot cell wall with a thickness of 0.6 m or more (over-the-wall operation);NOTERemote manipulators provide translation of human operator actions to a remote operating arm and terminal fixture. They may be of a “master/slave” type or operated by joystick or keypad.high-density (lead glass or other) radiation shielding windows greater than 0.09 m2 on cold area and with a density greater than 3 g/cm3 and a thickness of 100 mm or greater; and specially designed frames therefor; andradiation-hardened TV cameras, or lenses therefor, specially designed or rated as radiation hardened to withstand greater than 5 x 104 Gy (Silicon) (5 x 106 rad (Silicon)) without operational degradation.Tritium facilities, plants and equipment, as follows:facilities or plants for the production, recovery, extraction, concentration or handling of tritium, tritium compounds or mixtures containing tritium; andequipment for those facilities or plants as follows:hydrogen or helium refrigeration units capable of cooling to 23 K (-250°C) or less, with heat removal capacity greater than 150 W; andhydrogen isotope storage or hydrogen isotope purification systems using metal hydrides as the storage or purification medium.Platinized catalysts specially designed or prepared for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water.Lithium isotope separation facilities or plants and systems and equipment for that purpose, as follows:facilities or plants for the separation of lithium isotopes;equipment for the separation of lithium isotopes based on the lithium-mercury amalgam process, as follows:packed liquid-liquid exchange columns specially designed for lithium amalgams;mercury and lithium amalgam pumps;lithium amalgam electrolysis cells; orevaporators for concentrated lithium hydroxide solution;ion exchange systems specially designed for lithium isotope separation and specially designed components for those systems; andchemical exchange systems (employing crown ethers, cryptands or lariat ethers) specially designed for lithium isotope separation and specially designed components for those systems.Target assemblies and components for the production of tritium, as follows:target assemblies, made of or containing lithium enriched in the lithium-6 isotope, specially designed for the production of tritium through irradiation, including insertion in a nuclear reactor; andcomponents specially designed for the target assemblies specified in paragraph (a).NOTEComponents specially designed for target assemblies for the production of tritium may include lithium pellets, tritium getters and specially coated cladding.Any equipment not otherwise included in paragraph B.2 if the equipment is intended, or there are reasonable grounds to suspect that it is intended, in whole or in part, for use in connection with the design, development, production, handling, operation, maintenance or storage of nuclear weapons or other nuclear explosive devices.B.3. Controlled Nuclear InformationTechnologyTechnical data for the design, production, construction, operation or maintenance of any item in this Part, including, but not limited to, blueprints, plans, diagrams, models, formulae, engineering designs and specifications, software, manuals and instructions, except data available to the public (e.g., publications, publicly available websites or that which has been made available without restrictions on its further dissemination).NOTETechnical data referred to in paragraph B.3.1 is subject to control under both tangible and intangible modes of transfer.Any information not otherwise included in paragraph B.3.1 if the information is intended, or there are reasonable grounds to suspect that it is intended, in whole or in part, for use in connection with the design, development, production, handling, operation, maintenance or storage of nuclear weapons or other nuclear explosive devices.SOR/2007-208, ss. 14 to 24(F), 25(E); SOR/2010-106, ss. 3 to 6, 7(E), 8(F), 9(F), 10 to 13, 14(F), 15 to 27SOR/2025-196, s. 6SOR/2025-196, s. 7SOR/2025-196, s. 8SOR/2025-196, s. 9SOR/2025-196, s. 10SOR/2025-196, s. 11SOR/2025-196, s. 12SOR/2025-196, s. 13(E)SOR/2025-196, s. 14SOR/2025-196, s. 15SOR/2025-196, s. 16SOR/2025-196, s. 17SOR/2025-196, s. 18SOR/2025-196, s. 19SOR/2025-196, s. 20SOR/2025-196, s. 21SOR/2025-196, s. 22SOR/2025-196, s. 23SOR/2025-196, s. 24SOR/2025-196, s. 25SOR/2025-196, s. 26SOR/2025-196, s. 27SOR/2025-196, s. 28SOR/2025-196, s. 29SOR/2025-196, s. 30SOR/2025-196, s. 31SOR/2025-196, s. 32SOR/2025-196, s. 33SOR/2025-196, s. 34SOR/2025-196, s. 35SOR/2025-196, s. 36SOR/2025-196, s. 37(E)SOR/2025-196, s. 38SOR/2025-196, s. 39SOR/2025-196, s. 40SOR/2025-196, s. 41SOR/2025-196, s. 42SOR/2025-196, s. 43SOR/2025-196, s. 44SOR/2025-196, s. 45SOR/2025-196, s. 46SOR/2025-196, s. 47SOR/2025-196, s. 48SOR/2025-196, s. 49SOR/2025-196, s. 50SOR/2025-196, s. 51SOR/2025-196, s. 52SOR/2025-196, s. 53SOR/2025-196, s. 54SOR/2025-196, s. 55SOR/2025-196, s. 56SOR/2025-196, s. 57SOR/2025-196, s. 58SOR/2025-196, s. 59SOR/2025-196, s. 60SOR/2025-196, s. 61SOR/2025-196, s. 62SOR/2025-196, s. 63SOR/2025-196, s. 64SOR/2025-196, s. 65SOR/2025-196, s. 66SOR/2025-196, s. 67SOR/2025-196, s. 68SOR/2025-196, s. 69SOR/2025-196, s. 70SOR/2025-196, s. 71SOR/2025-196, s. 72SOR/2025-196, s. 73AMENDMENTS NOT IN FORCE
— SOR/2025-196, s. 3Paragraph 3(1)(a) of the Nuclear Non-proliferation Import and Export Control Regulations2 is replaced by the following:SOR/2000-210the applicant’s business number assigned by the Canada Revenue Agency, if applicable, their name, Canadian address, email address and telephone number;Subsection 3(1) of the Regulations is amended by striking out “and” at the end of paragraph (g), by adding “and” at the end of paragraph (h) and by adding the following after paragraph (h):the applicant’s written process for the import or export of the substance, equipment or information.
— SOR/2025-196, s. 4The Regulations are amended by adding the following after section 3:Record RetentionEvery person must retain, for a period of six years after the day on which a licence to import or export issued to them expires, the licence and all records relevant to any import or export under it, including, if applicable,the application for the licence and supporting information submitted to the Commission or any designated officer who is authorized to carry out the duties set out in paragraphs 37(2)(c) and (d) of the Act;the customs declaration and associated documentation submitted at the time of import or export;shipping manifests and associated documentation;any purchase order and certificate of manufacture; andthe notifications and other reporting submissions made under the licence.SOR/2025-1962026-03-25SOR/2025-1962025-09-26